SFP-10G-T 10GBASE-T Copper SFP+ Transceiver

SFP-10G-T 10GBASE-T Copper SFP+ Transceiver

Up to 10Gb/s bi-directional data links Hot-pluggable SFP+ footprint Fully metallic enclosure for low EMI Low power dissipation Compact RJ-45 connector assembly Access to physical layer IC via 2-wire serial bus Supports Links up to 30m using Cat 6a/7 Cable RoHS Compliant Operating case temperature: 0℃ to 70℃

Download instructions

SFP_10G_T.pdf

Specifications

 
Description  of this SFP-10G-T 10GBASE-T Copper SFP+ Transceiver
 
Features
  • Up to 10Gb/s bi-directional data links
  • Hot-pluggable SFP+ footprint
  • Fully metallic enclosure for low EMI
  • Low power dissipation
  • Compact RJ-45 connector assembly
  • Access to physical layer IC via 2-wire serial bus
  • Supports Links up to 30m using Cat 6a/7 Cable
  • RoHS Compliant
  • Operating case temperature: 0℃ to 70℃

Applications

  • 10 Gigabit Ethernet over Cat 6a/7 cable

Description

SFP-10G-T Copper Small Form Pluggable (SFP) transceivers are high performance, cost effective module compliant with the 10G Ethernet and 10GBASE-T standards as specified in IEEE 802.3az, which supporting 10Gbps data- rate up to 30 meters reach over unshielded twisted-pair category 6a/7 cables. The module provides standard serial ID information compliant with SFP+ MSA, which can be accessed with address of A0h via the 2wire serial EEPROM protocol. The physical IC can also be accessed via 2wire serial bus at address A0h.

Parameter of this SFP-10G-T 10GBASE-T Copper SFP+ Transceiver
 
Cable Length
 

Standard

Cable

Reach

Host Port

10Gbase-T

CAT6A

30m

XFI

 

Specification

+3.3V Volt Electrical Power Interface

Parameter

Symbol

Min

Typical

Max

Unit

Notes

Input Voltage

Vcc

3.13

3.3

3.47

V

 

Supply Current

Icc

 

700

900

mA

3.0W max power over full range of voltage and temperature.See caution note below

Maximum Voltage

Vmax

-0.3

 

4.0

V

  

Surge Current

Surge

 

TBD

 

mA

 

Current

 

current See caution note

        

Notes:

  1. Power consumption and surge current are higher than the specified values in the SFP MSA.

Low-Speed Signals Electronic Characteristics

Parameter

Symbol

Min

Typical

Max

Unit

Notes

  SFP Output LOW

VOL

0

 

0.5

 

V

4.7k to 10k pull-up to host_ Vcc.   

  SFP Output HIGH

VOH

host_Vcc -0.5

 

host_Vcc +0.3

V

4.7k to 10k pull-up to host_ Vcc.   

  SFP Input LOW

VIL

0

 

0.8

V

4.7k to 10k pull-up to host_ Vcc.   

  SFP Input HIGH

VIH

2

 

Vcc + 0.3

V

4.7k to 10k pull-up to host_ Vcc.   

High-Speed Electrical Interface, Transmission Line-SFP

Parameter

Symbol

Min

Typical

Max

Unit

Notes

  Line Frequency

fL

 

125

 

MHz

5-level encoding, per IEEE 802.3

  Tx Output Impedance

Zout,TX

 

100

 

Ohm

Differential

  Rx Input Impedance

Zin,RX

 

100

 

Ohm

Differential

High-Speed Electrical Interface, Transmission Line-SFP

  Single Ended Data Input Swing

Vinsing

250

 

1200

mV

Single ended

  Single Ended Data Output Swing

Voutsing

350

 

800

mV

Single ended

  Rise/Fall Time

Tr,Tf

 

175

 

ps

20%-80%

  Tx Input Impedance

Zin

 

50

 

Ohm

Single ended

  Rx Output Impedance

Zout

 

50

 

Ohm

Single ended

 

General Specifications

Parameter

Symbol

Min

Typical

Max

Unit

Notes

  Data Rate

BR

10

 

1000

Mb/s

  IEEE 802.3 compatible

  Storage temperature

TS

-40

 

85

  Case temperature

  Operating temperature range

Top

0

 

60

  Ambient temperature

  I 2C Clock Rate

 

0

 

200,000

Hz

 

Notes:

  • Clock tolerance is +/- 50 ppm.
  • By default, the 10G Copper SFP is a full duplex device in preferred master mode.
  • Automatic crossover detection is enabled. External crossover cable is not required.
  • By default, 1000 GBASE-T operation requires the host system to have an SERDES interface with no clocks.

 Pin Descriptions

As Viewed Through Top of Board
As Viewed Through Top of Board

 

Pin

Symbol

Function/Description

Ref.

1

VeeT

Transmitter Ground

1

2

TX  Fault

Transmitter Fault Indication

 

3

TX Disable

Transmitter Disable-Module disables on high or open

 

4

MOD-DEF2

Module Definition 2-Two wire serial ID interface

2

5

MOD-DEF1

Module Definition 1-Two wire serial ID interface

2

6

MOD-DEF0

Module Definition 0-Two wire serial ID interface

2

7

Rate Select

Not Connected

 

8

LOS

Loss of Signal

3

9

VeeR

Receiver Ground

1

10

VeeR

Receiver Ground

1

11

VeeR

Receiver Ground

1

12

RD-

Inverse Received Data out

 

13

RD+

Received Data out

 

14

VeeR

Receiver Ground

1

15

VccR

Receiver Power

 

16

VccT

Transmitter Power

 

17

VeeT

Transmitter Ground

1

18

TD+

Transmitter Non-Inverted Data In

 

19

TD-

Transmitter Inverted Data In

 

20

VeeT

Transmitter Ground

1

Notes:

  • Circuit ground is connected to chassis ground.
  • Should be pulled up with 4.7k - 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF (0) pulls line low to indicate module is plugged in.
  • LVTTL compatible with a maximum voltage of 2.5V.

Mechanical Dimensions

Dimensions are in millimeters. All dimensions are ±0.2mm unless otherwise specified.    (Unit: mm)

 

Ordering information

Model No.

Product Description

SFP-10G-T

10G Copper SFP+ 0~70°C

 
Image  of this SFP-10G-T 10GBASE-T Copper SFP+ Transceiver
 
  
Our Factory of this SFP-10G-T 10GBASE-T Copper SFP+ Transceiver

Our factory has more experience in production SFP-10G-T 10GBASE-T Copper SFP+ Transceiver,and we can provide multiple types related products. If you want to know more details about these, welcome to contact us!

Our Service  of this SFP-10G-T 10GBASE-T Copper SFP+ Transceiver

We have standardization process in production SFP-10G-T 10GBASE-T Copper SFP+ Transceiver, and ensuring our product’s quality.We have professional pre-sales team, they can answer your each questions.We have hard-working after-sales team, who are providing after-sales service and protection for our clients.

Corporate vision:To be the benchmark for the optical fiber industry.

Corporate Mission:Leading the industry; Providing satisfiedcommunication products, solutions and services to worldwide customers.

 To invest in both personal and corporate growth simultaneously.

Core Values:Creating Customer Value. Insisting on R & D and Innovation. Building a Global Network. Adhering to Humanistic Management .

 Looking forward to your inquiry for this SFP-10G-T 10GBASE-T Copper SFP+ Transceiver.


You might also like